Series B Tanks – Diesel & Petrol

A range of black fuel tanks, available in 6 different sizes. These tanks are CE approved and comply with ISO 10088 standard.
Each tank is supplied with the following connections:
- 38 mm vented filler cap
- 5 hole blind cover for fuel tanks level indicator (Ref: S3-17.5-S3-25)
- 8 mm elbow hosetail with pickup pipe for fuel suction
- arrangement for diesel fuel return fitting (Ref: TT-44624)
- 2 additional blind holes for an alternative vent fitting (Ref: TT-44568-straight hosetail for 20 mm hose, Ref: TT-44567-straight hosetail for 16 mm hose)

Series B Tanks – Water

A range of white tanks for water, available in 6 different sizes.
Each tanks is supplied with the following connections:
- 38 mm vented filler cap
- 5 hole blind cover for water tank level indicator (Ref: S3-17.5-S3-25)
- 16 mm elbow hosetail with pickup pipe for water suction
- 1 additional threaded and blind hole for gravity feed under the filler
- 2 additional blind holes for an alternative vent fitting (Ref: TT-44568-straight hosetail for 20 mm hose, Ref: TT-44567-straight hosetail for 16 mm hose)

Series B Tanks – Waste

A range of blue tanks to handle your waste wateron board in full compliance with ISO 8099 standard.
Available in two different models:

Horizontal
Designed to save on space, provided with the plastic loops in the top to hold either a macerator or diaphragm pump in position without the need for screws and bolts.
Fitting options:
- 1 x 3/4 BSP Female (Vent)
- 2 x 1 1/2 BSP Male with Dip Pipe (Outlets)
- 6 x 1 1/2 BSP Blanked off Female (Inlets/Outlets)

Vertical
Ideally suited for mounting on a bulkhead as their “V” shape bottom will allow easier discharge.
Fitting options:
- 1 x 3/4 BSP Female (Vent)
- 2 x 1 1/2 BSP Male with Dip Pipe (Outlets)
- 1 x 1 1/2 BSP Female (Inlet)

Each tank is supplied with an inspection hatch with a diameter of 127 mm and 5 hole blind cover to accept waste tank level indicator.

Series C Tanks – Diesel & Petrol

Series C Tanks – Water

Series C Water Tanks are available in 2 versions:

1. Series C Supreme.

Manufactured in Italy from High Density Polyethylene these tanks are white in colour and come complete with:
- inspection cover
- filler cap with vent 
- 1/2″ water connection fitting and pickup pipe.
There is provision to fit a level indicator (Ref: S3-30 or S3-40) suitable for use with WEMA analogue gauge (Ref: IPWR)

More Information:

Series C Water Tank Brochure

Manufactured in Italy these are green rigid plastic tanks with threaded inspection porthole, with strengthening ribs above and below tank.
The inspection hatch is sealed with a foam rubber gasket which will not take a huge amount of pressure.
Tek-tanks can supply an upgrade which is attached using 10 screws and comes with a solid rubber gasket and welded fittings. This combination will allow a greater internal pressure due to a high fill point.
Please click here to see the picture of our custom water inspection hatch.

Buy Series C Fittings and Accessories Online

Series C Tanks – Waste

Series C Tanks Waste

An excellent range of sensibly priced waste holding tanks manufactured in Italy. Moulded with a thicker wall than the equivilent green water tanks in the Series C range to combat odour problems normally associated with moulded tanks.

Fitting sizes are 1 1/2″ Inlet, 1 1/2″ Pumpout and 1″ Vent.
All mounted on an inspection plate which is removable.

Fittings can be supplied with either elbows or straights (please specify when ordering).

More Information:

Series C Waste Tank Brochure